# Standpipe Flow Test: Requirements, Procedure and Results

- Link: https://fourpointfire.com/blog/standpipe-flow-test/
- Published: 2026-11-17T23:01:36-07:00
- Author: FourPoint Fire & Water

A standpipe flow test proves that the water supply, underground piping, valves and
risers of your standpipe system can still deliver the design flow and pressure at
the hydraulically most remote hose connection (the outlet that is hardest for water
to reach). For automatic standpipes, NFPA 25 sets this test at every five years.
It is a separate test from a hydrostatic test, and passing one does not satisfy 
the other. We service fire hydrants, sprinkler systems, standpipes, backflow prevention,
cross-connection control and related underground piping in Grande Prairie, Dawson
Creek and the Peace Region, and the supply side of a flow test, hydrants and underground
mains included, is where many failed tests start.

Fourpointfire

fourpointfire.com

Confirm Your Standpipe Supply

FourPoint assesses fire safety systems in their operating context, helping you understand
hydrant and underground piping conditions that affect flow.

[Visit](https://fourpointfire.com/)

## TL;DR

 * A flow test measures water delivery at the most remote hose connection. A hydrostatic
   test only checks that piping holds pressure without leaking.
 * Under NFPA 25, [automatic standpipes need a full-demand flow test every five years](https://nfsa.org/understanding-the-five-year-inspection-and-testing-requirements-for-manual-and-automatic-standpipe-systems/),
   and a partial flow does not meet the intent.
 * Manual and semiautomatic dry standpipes need a five-year hydrostatic test, normally
   at not less than 200 psi (13.8 bar) for two hours.
 * Your authority having jurisdiction (AHJ, the fire department or code official
   who enforces the code) sets the exact rules, so confirm the edition and method
   with them before test day.
 * Keep the full report with static, residual and flow readings. Inspectors expect
   it.

## Table of Contents

 * [What a standpipe flow test actually checks](https://fourpointfire.com/blog/standpipe-flow-test/#what-a-standpipe-flow-test-actually-checks)
 * [Which Canadian rules apply](https://fourpointfire.com/blog/standpipe-flow-test/#which-canadian-rules-apply)
 * [How a standpipe flow test is run](https://fourpointfire.com/blog/standpipe-flow-test/#how-a-standpipe-flow-test-is-run)
 * [What counts as a passing result](https://fourpointfire.com/blog/standpipe-flow-test/#what-counts-as-a-passing-result)
 * [Records the inspector will ask for](https://fourpointfire.com/blog/standpipe-flow-test/#records-the-inspector-will-ask-for)
 * [When the test finds a deficiency](https://fourpointfire.com/blog/standpipe-flow-test/#when-the-test-finds-a-deficiency)
 * [Our approach to standpipe flow testing](https://fourpointfire.com/blog/standpipe-flow-test/#our-approach-to-standpipe-flow-testing)
 * [Standpipe service in the Peace Region](https://fourpointfire.com/blog/standpipe-flow-test/#standpipe-service-in-the-peace-region)
 * [FAQ](https://fourpointfire.com/blog/standpipe-flow-test/#faq)
 * [Sources](https://fourpointfire.com/blog/standpipe-flow-test/#sources)

## What a standpipe flow test actually checks

A standpipe is a rigid pipe system, usually in a stairwell or along a building’s
perimeter, that lets firefighters connect hose at a floor without running hose from
the street. Class I connections are 2½-inch valves for fire department use. Class
II connections carry smaller hose for occupant or trained-brigade use, and Class
III combines both.

The flow test answers one question: if the system were needed today, would the water
arrive at the pressure and volume it was designed for? Per the National Fire Sprinkler
Association, a flow test evaluates [actual system performance under operating conditions](https://nfsa.org/understanding-the-five-year-inspection-and-testing-requirements-for-manual-and-automatic-standpipe-systems/),
confirming that the water supply, underground piping, fire pump, risers, valves 
and standpipe piping perform as designed.

That last point matters for property managers. A standpipe is only as good as what
feeds it. A partly closed valve on the supply, a tuberculated or silted underground
main, or a municipal supply that has changed since the building was designed can
each pull the result down even when every riser inside the building is sound.

### Flow test or hydrostatic test

The two are often confused on work orders.

  |   |  Flow test |  Hydrostatic test |  
   |  What it proves |  Water delivery at design flow and residual pressure |  Piping holds pressure without leakage or failure |  
 |  Typical system |  Automatic standpipes (wet or dry) |  Manual and semiautomatic dry standpipes, dry portions of others |  
 |  Interval under NFPA 25 |  Every five years |  Every five years |  
 |  Evaluates supply capability |  Yes |  No |

The [City of Vancouver’s standpipe testing bulletin](https://vancouver.ca/files/cov/vfrs-bulletin-standpipe-system-testing.pdf)
draws the same line: automatic wet standpipes require flow tests only, while manual
and semiautomatic dry systems, including the fire department connection piping, 
require the hydrostatic test.

## Which Canadian rules apply

Standpipe testing in Canada is not governed by a single national schedule. Provincial
fire codes adopt or reference NFPA 25, and each municipality’s fire department enforces
it. In Alberta, where our work is focused, we recommend confirming the fire code
edition and any local bulletin with your AHJ. Examples from other provinces show
the pattern you will see:

 * **Vancouver, BC.** Under the Vancouver Fire By-law, which references NFPA 25,
   [a flow test is required every five years](https://vancouver.ca/files/cov/vfrs-bulletin-standpipe-system-testing.pdf)
   on all automatic standpipe systems, at the hydraulically most remote hose valve
   outlets while flowing the system demand.
 * **Ontario.** The [Ontario Fire Code (O. Reg. 108/18)](https://www.ontario.ca/laws/regulation/r18108)
   requires flow and pressure tests at the highest and most remote hose valve or
   connection, requires them annually in buildings containing a hotel, and requires
   hydrostatic testing of dry standpipe piping at intervals not exceeding five years.
 * **Weyburn, Saskatchewan.** The town’s [standpipe requirements table](https://weyburn.ca/wp-content/uploads/2024/04/Standpipe-and-Hose-Systems-Requirements.pdf)
   lists a five-year flow test by an authorized person, plus annual inspection including
   a main drain test, quarterly hose valve inspections and monthly gauge and hose
   cabinet checks.

For new or altered systems, design data matters too. The City of London, Ontario,
notes that [hydraulic calculations must use hydrant flow test data no older than 12 months](https://london.ca/sites/default/files/2026-03/Standpipe%20Systems.pdf).
That is a useful reminder that hydrant flow testing and standpipe flow testing are
linked: the hydrant results describe the supply, and the standpipe test shows whether
the building’s piping can use it.

### Events that trigger an extra test

The five-year interval is the routine. Ontario’s code and Weyburn’s table both call
for flow and pressure testing after a system is modified, extended, or returned 
to service after more than a year out of use. Treat any major alteration, long shutdown,
fire pump replacement or change to the water supply as a reason to ask your AHJ 
whether an unscheduled test is expected.

## How a standpipe flow test is run

The sequence below follows the City of Vancouver bulletin and NFPA 25. Your AHJ 
may add or change steps, so agree the method with them in advance. NFPA 25 itself
says the test method and performance criteria should be [discussed with the AHJ ahead of time](https://asc.modares.ac.ir/uploads/Shr.Technical.Rar.116.pdf).

 1.  **Establish what you have.** Confirm the standpipe type (automatic, semiautomatic
     or manual; wet or dry), the original approved design, any modifications, the available
     supply and the test boundaries. Do not assume every standpipe on your portfolio
     carries identical testing obligations.
 2.  **Use qualified personnel.** Vancouver requires that hydrostatic and flow testing
     be performed by qualified people. Arrange this early, because testing is scheduled
     around the building’s occupants and the water supply.
 3.  **Notify the right people.** Tell building management, tenants, the monitoring
     company and the AHJ. Flowing water can trigger a waterflow alarm, which is expected,
     but it should not surprise anyone or dispatch a response.
 4.  **Inspect before you flow.** Cycle the hose valves fully, thread-test them with
     a test coupling, and check fire department connection couplings and swivels. Vancouver’s
     bulletin also asks testers to check for hose connections that could exceed 175
     psi during flow, and to run an air test before introducing water to manual dry
     systems.
 5.  **Plan the water discharge.** Water has to go somewhere that can handle it. Vancouver
     requires discharge within property lines, and a permit for discharge onto city
     property or for hydrant use. In the Peace Region, check with the municipality 
     or utility before any hydrant is opened.
 6.  **Record static pressure.** This is pressure with no water flowing, measured at
     the gauge location.
 7.  **Flow at the most remote connection.** Connect the flow equipment at the hydraulically
     most remote outlet of each zone and flow to the required demand. Typical equipment
     is a pitot gauge or flow meter, calibrated pressure gauges, a smooth-bore nozzle
     and hose to carry the water away.
 8.  **Record residual pressure and flow.** Residual pressure is what remains in the
     system while water is flowing. Note inlet and outlet pressures at any pressure-
     regulating valves.
 9.  **Confirm alarms and check for leaks.** The waterflow alarm should activate, and
     piping, valves and connections should show no leakage.
 10. **Restore the system.** Return every valve to its normal position, drain and reset
     as needed, and confirm the system is back in service.

### Where tests go wrong

Most delays come from preparation, not the flow itself. Common causes include a 
supply valve found closed, seized hose valves that cannot be cycled, no drainage
path for the discharge, or a test attempted with only a partial flow. NFSA’s Terin
Hopkins cautions that [partial-flow testing does not satisfy NFPA 25’s intent](https://nfsa.org/understanding-the-five-year-inspection-and-testing-requirements-for-manual-and-automatic-standpipe-systems/)
for automatic standpipes, which should be tested at full required flow.

## What counts as a passing result

NFPA 25 requires the five-year test to verify that the water supply still provides
the design pressure at the required flow at the hydraulically most remote hose connection
of each zone. Systems are tested to the requirements in effect when they were installed,
which is why the original design documents matter.

Under NFPA 14, the standard for standpipe design, system demand is the flow rate
and residual pressure needed at that most remote connection. NFSA explains that 
for Class I standpipes the acceptance test involves [a minimum residual of 100 psi through the two most remote 2½-inch hose valves](https://nfsa.org/standpipe-flow-testing/),
with flow of up to 1,000 gpm (1,250 gpm in non-sprinklered buildings) and 250 gpm
for each additional standpipe. Class II systems in Ontario’s London guide call for
a [minimum of 6.3 L/s (100 gpm) at the most remote hose connection](https://london.ca/sites/default/files/2026-03/Standpipe%20Systems.pdf).

![Class I and II standpipe test requirements](https://fourpointfire.com/blog/wp-
content/uploads/2026/11/1794877995387_Class-I-and-II-standpipe-test-requirements.
jpeg)

Because the design values depend on installation date, class and building, the number
you must hit is the one in your approved design, confirmed with your AHJ. Compare
your readings against it, not against a generic figure.

### What a worked example looks like

Suppose a four-storey commercial building has an automatic wet standpipe designed
for a given demand at the roof outlet. On test day the static pressure is recorded,
then water is flowed at the full required rate through the roof outlet. If the residual
pressure at that flow falls short of the design figure, the system has not passed,
even if every valve cycles cleanly. The usual next questions are whether a supply
valve is partly closed, whether the underground main has lost capacity, or whether
the municipal supply has changed. These are supply-side problems, and they are why
hydrant and underground piping condition belongs in the same conversation. Our note
on [what hydrant pressure testing measures](https://www.fourpointfire.com/blog/hydrant-pressure-testing)
explains the supply-side readings in more detail.

![What a worked example looks like](https://fourpointfire.com/blog/wp-content/uploads/
2026/11/1794877978570_What-a-worked-example-looks-like.jpeg)

## Records the inspector will ask for

A flow test that is not documented has not happened as far as an inspector is concerned.
The report should identify the systems tested, describe the procedure and method,
and record complete results: static and residual pressures, flow rates, alarm function
and valve positions. Vancouver requires that the completed report go to the building
owner or their representative, with a copy [kept in the fire safety plan](https://vancouver.ca/files/cov/vfrs-bulletin-standpipe-system-testing.pdf)
for the fire department to inspect.

A few habits make audits easier:

 * Store every five-year report with the original design documents so the next tester
   knows what the system was designed to deliver.
 * Log the date, tester, equipment used and the AHJ’s agreed method.
 * Note any deficiency with the date it was found and the date it was corrected.
 * Keep dry standpipe hydrostatic reports with flow reports, but never substitute
   one for the other.

If your team is tightening how test and compliance paperwork is organized, these
[professional recordkeeping best practices](https://24hourcontractor.com/resources/professional-recordkeeping-best-practices-for-bc-residential-builders)
cover habits that carry over to fire protection files.

## When the test finds a deficiency

A failed or marginal result is information, and the sequence that follows is practical:

 1. Confirm the reading by checking gauges and equipment calibration.
 2. Check the supply path: control valves, backflow assemblies, the fire pump if there
    is one, and the underground piping.
 3. Repair what is found, whether that is a valve, a hose connection, a leaking joint
    or a section of underground main.
 4. Retest the affected zone and document both the failure and the corrected result.
 5. Tell the AHJ if the system was impaired, and follow their guidance on interim measures.

Standpipes seldom fail in isolation. A backflow preventer on the supply can restrict
flow, a frozen or damaged hydrant can cut the municipal side, and underground piping
can lose capacity. A contractor who can work on all of those avoids the hand-offs
that stretch out a retest.

## Our approach to standpipe flow testing

> Property managers often call us when a five-year date is approaching, or after
> an inspector has asked for a report they cannot find. In both cases the first 
> thing we want is the paper: the standpipe class, the original design demand and
> the last report. A flow test is only meaningful against a design number.
> The second thing we look at is the supply. We work on fire hydrants every day,
> so we think about the full path water takes from the main to the most remote hose
> valve, including hydrants, underground piping, backflow assemblies and the standpipe
> itself. That context lets us explain a marginal result rather than only record
> it.
> Our services include inspection, installation, maintenance, design and consulting,
> and I lead the work as a Red Seal Journeyman Sprinkler Fitter. I entered the trade
> in 2001 and earned my journeyman ticket in 2014. We make no promises about results,
> and we do not arrange work until the scope, the site context and the equipment
> details are clear to you.
> _Kevin_

## Standpipe service in the Peace Region

FourPoint Fire & Water works with commercial property managers, industrial facilities
and municipalities on [standpipe system inspection and maintenance](https://www.fourpointfire.com/standpipe-systems.html),
and on the hydrants and underground piping that supply them. For hydrants specifically,
that includes [inspection](https://www.fourpointfire.com/hydrant-inspection.html),
[maintenance](https://www.fourpointfire.com/hydrant-maintenance.html), [repair](https://www.fourpointfire.com/hydrant-repair.html),
replacement, installation and excavation. We also handle sprinkler systems, backflow
prevention and cross-connection control.

Our service area is Grande Prairie, Dawson Creek and the Peace Region, and we offer
24 hour emergency response for locations within 200 km. Contact us to confirm availability
for your location, and bring your last standpipe report and design documents if 
you have them.

![Fourpointfire](https://fourpointfire.com/blog/wp-content/uploads/2026/11/1794453426692_fourpointfire.
jpg)

To start a conversation about scope, see our [standpipe systems page](https://www.fourpointfire.com/standpipe-systems.html)
or reach us through [fourpointfire.com](https://fourpointfire.com).

## FAQ

### How often does a standpipe need a flow test?

Under NFPA 25, automatic standpipe systems need a full-demand flow test every five
years. Some codes add more frequent testing: Ontario requires annual flow and pressure
tests in buildings containing a hotel. Confirm the edition and any local schedule
with your AHJ.

### Is a standpipe flow test the same as a hydrostatic test?

No. A flow test measures delivered flow and residual pressure at the most remote
connection. A hydrostatic test, normally at not less than 200 psi (13.8 bar) for
two hours on manual and semiautomatic dry standpipes, checks only that piping holds
pressure without leakage. Each answers a different question, and one does not replace
the other.

### What psi should a standpipe flow at?

There is no single number. The target is the design demand for your system, set 
by its class and installation requirements. For Class I standpipes tested under 
NFPA 14, NFSA describes a minimum 100 psi residual through the two most remote 2
½-inch hose valves. Your approved design and AHJ confirm the figure for your building.

### Who is allowed to perform the test?

Qualified personnel. Vancouver’s bulletin requires this for both flow and hydrostatic
tests, and Weyburn’s table specifies an authorized person for the five-year flow
test. Ask your AHJ what qualifications they accept in your area.

### Do we need a permit to discharge the water?

It depends on where the water goes. Vancouver requires discharge within property
lines and a permit for discharge onto city property or hydrant use. Check with your
municipality or water utility before test day.

Fourpointfire

Discuss Your Standpipe Test

Contact FourPoint to discuss your fire safety system and the inspection, maintenance
or repair needs specific to your property.

FFourpointfire

[Call FourPoint+1 587 297 2336](https://fourpointfire.com/blog/standpipe-flow-test/+15872972336)

## Sources

 * [City of Vancouver, Standpipe system testing bulletin](https://vancouver.ca/files/cov/vfrs-bulletin-standpipe-system-testing.pdf)
 * [NFSA, Understanding the five-year inspection and testing requirements for standpipe systems](https://nfsa.org/understanding-the-five-year-inspection-and-testing-requirements-for-manual-and-automatic-standpipe-systems/)
 * [NFSA, Understanding standpipe flow testing](https://nfsa.org/standpipe-flow-testing/)
 * [Ontario Fire Code, O. Reg. 108/18](https://www.ontario.ca/laws/regulation/r18108)
 * [City of London, Standpipe Systems guide](https://london.ca/sites/default/files/2026-03/Standpipe%20Systems.pdf)
 * [Town of Weyburn, Standpipe and Hose Systems Requirements](https://weyburn.ca/wp-content/uploads/2024/04/Standpipe-and-Hose-Systems-Requirements.pdf)
 * [NFPA 25, standpipe testing text](https://asc.modares.ac.ir/uploads/Shr.Technical.Rar.116.pdf)

## Recommended

 * [Hydrant Pressure Testing: What It Measures](https://www.fourpointfire.com/blog/hydrant-pressure-testing)
 * [Standpipe Inspection & Maintenance](https://www.fourpointfire.com/standpipe-systems.html)
 * [Fire Hydrant Inspection](https://www.fourpointfire.com/hydrant-inspection.html)
 * [Sprinkler Inspections](https://www.fourpointfire.com/sprinkler-inspections.html)
